Raleigh - Durham - Chapel Hill - Cary/ApexCarrboro   Hours At All Locations: Mo-Sa 10-7, Su 12-5  Dedicated Parking At All Locations


Visa MasterCard American Express Discover

Bicycle Lubrication

Bicycles are made up of many parts that work best and last longest when properly lubed. View this diagram to see the lube points for modern bicycles. Below, we explain what's involved.

Lubricants & Grease

The lubricant used the most is a liquid lube, which we sell in small drip and spray containers. We recommend purchasing our cycling-specific lubes because they're perfectly formulated for your two-wheeler. This matters because the typical all-around lubes sold at hardware stores are often too thick or too thin to lubricate your bike properly. And, they'll usually leave an oily residue that can make a mess of your machine and clothing. Also, some products will attack the seals on bike components damaging your equipment.

Liquid lubes come in a wide and sometimes confusing variety. We can recommend one perfect for your bike and our riding conditions. You only need a small container and it'll last for many rides.

Depending on how much you plan to work on your bike, you may want to pick up some grease, too. This is a thicker lube, about the consistency of Crisco shortening. We sell it in squeeze tubes.

You can't see it, but grease is what's inside the headset (steering mechanism), hubs, bottom bracket and pedals. There are bearings inside these components and they sit in a bed of grease that keeps them lubed and turning freely.

Because grease is thick and these systems are protected from the elements, it's unlikely you'll need to work on these parts. However, grease is also used to lubricate threads and parts that fit together, such as the seatpost and stem and the associated bolts. If you plan to work on these parts, it's good to have some grease on hand.

Lubing It Part By Part

How often you lube your bike depends on how you use it. Ideally, the moving parts will always be lightly lubed. A dry, squeaking bike needs lube. A bike covered with grime means you're using too much lube (or the wrong lube).

Applying lube is just a matter of dripping or spraying some on, operating the part to get the lube down inside, letting it sit for a bit for the lube to fully penetrate and then wiping off the excess.

Chain: lubricate the lower run of links (see diagram) as you pedal backwards with your hand until you've lightly coated the entire chain.

Brakes: lube the pivot points where the brake parts move against each other. If there's a quick-release mechanism and/or adjustment barrel (sometimes on the brake lever; see diagram), lightly lube these, too (on the threads for the adjustment barrel). Do NOT get lube on the brake pads or rims!

Derailleurs: wet the pivot points on the derailleur bodies. And, for the rear, while the bike's resting on its side, apply a little to the center of the derailleur pulleys. Lube the adjustment barrel, too.

Clipless pedals: apply lube if your shoes and pedals are creaking when you ride and/or it's difficult to get in or out. Remember to remove your shoes before walking into the house so you don't leave oily footprints across the carpet! 

Cables: most brake and shift cables don't require lube because they're inside nylon-lined housing. If yours bind, however, you can add lube if your bike has split housing stops. These allow accessing the cables and lubing. It's done by opening the brake quick release to create slack and then pulling slightly to free the housing from the frame stops. You can then slide the housing to get at the cable inside. For derailleurs, shift onto the largest cog or ring and then move the levers back without pedaling. This creates enough slack to get the housing out of the stops and lube the shift cables (if necessary, don't forget to lube where the cables pass beneath the bottom bracket, too).

Suspension fork: double-check that your lube won't harm nylon or rubber seals. If it's safe, you can apply a few drops to the upper fork legs and push down on your handlebars a few times to compress the fork and work the lube past the seals. This will keep the fork's action smooth.


Feature Items

Specialized Jynx Comp 650B - Women's
Specialized Jynx Comp 650B - Women's - 2015

Specialized’s Jynx Comp 650B comes ready to tackle everything in its path. Its lightweight aluminum frame has a balanced, women’s-specific geometry… [more]

Specialized Ruby Compact - Women's
Specialized Ruby Compact - Women's - 2013
Product Rating
5.0 stars
 (1 Review)

Specialized's Ruby Compact balances comfort with speed and stability. The secret is Specialized's super-light, comfortable FACT 8r-carbon frame with… [more]

Specialized Pitch 650B
Specialized Pitch 650B - 2015/2016
Product Rating
3.0 stars
 (1 Review)

Ride it all with newfound confidence aboard Specialized’s Pitch 650B. A lightweight aluminum frame with balanced geometry is matched to 650B wheels… [more]

Raleigh Sojourn
Raleigh Sojourn - 2014
Product Rating
5.0 stars
 (2 Reviews)

Raleigh's Sojourn is a bike built for the open road and exploring the far side of every hill. Its renowned Reynolds chromoly frameset is strong,… [more]

Specialized S-Works CruX Di2
Specialized S-Works CruX Di2 - 2015

Looking to dominate the cross series? Specialized's S-Works CruX Di2 uses a lightweight FACT 11r carbon frame that's full of cross-oriented touches… [more]